1. kong u's Avatar
    Does anybody know what size the torx screws are on the base of the 920?

    Thought I read somewhere that it was T5 or T6 so I went and ordered some but theyre not the right size, too big.

    If anybody knows the exact size head that would be sweet.

    Thanks
    Last edited by kong u; 01-08-2013 at 02:08 PM.
    01-08-2013 07:29 AM
  2. ttsoldier's Avatar
    T2 , T4 and T5
    01-08-2013 07:40 AM
  3. phirefly's Avatar
    T5 on the bottom of the phone.
    01-08-2013 07:56 AM
  4. MS_SURVEYOR's Avatar
    01-08-2013 08:06 AM
  5. HIllste1's Avatar
    Torx + Size 5 M2.5 x 9.7 is exactly what called out in the Repair Manual.
    01-08-2013 08:28 AM
  6. 920Walker's Avatar
    The torx tool bit size is probably T-5.

    M2.5 is the screw's metric thread diameter and 9.7 is the length, all in mm.
    01-08-2013 08:33 AM
  7. kong u's Avatar
    Just watched the DIY video and the poster says they're T5 screws, but according to the torx set that I bought, they're not. The set ranges from T5-T10 and T5 is way too big.

    Unless the screwdriver set I bought was wrong then maybe phones vary. I'm from the UK and it sounds like the poster is too so I'm stumped!
    01-08-2013 02:25 PM
  8. 920Walker's Avatar
    I just checked too. Way smaller than T-5. I have a micro screwdriver set with tiny torx buts and even the smallest doesn't fit.

    Edit: It is T5. .055", 1.40mm. The smallest in my micro screwdriver kit was T6 and I found another micro kit i purchased with even smaller torx bits. The biggest being t5, and it fits.
    Last edited by 920Walker; 01-08-2013 at 02:44 PM.
    01-08-2013 02:32 PM
  9. palandri's Avatar
    On my Nokia N8 it was a T4 I found one on Amazon, but it took like 2 weeks for the company to mail it.
    01-08-2013 02:36 PM
  10. ttsoldier's Avatar
    I just checked too. Way smaller than T-5. I have a micro screwdriver set with tiny torx buts and even the smallest doesn't fit.
    T2 , T4 and T5
    ...
    01-08-2013 02:38 PM
  11. Rhody#WP's Avatar
    I got my 920 open, but I can't separate the motherboard from the screen. The screw seems way too tiny. I have a T2 and an even smaller screw driver (T1 or hex 1.5?), and they're both too big. Does anybody know what size the screw is?
    03-20-2014 07:57 AM
  12. thejaredhuang's Avatar
    I guarantee its a T2 unless someone else messed with your phone. I've replaced the digitizer on 5 920s and I've only used T5s and T2s for assembly/diassembly.
    03-21-2014 01:16 AM
  13. Rhody#WP's Avatar
    I guarantee its a T2 unless someone else messed with your phone. I've replaced the digitizer on 5 920s and I've only used T5s and T2s for assembly/diassembly.
    It was a T1.

    Edit: For some reason I needed a T1 to get the screws out, but a T2 worked just fine putting them back in. You are correct, they are T2 screws.
    Last edited by Rhody#WP; 03-30-2014 at 08:53 AM.
    03-28-2014 08:33 AM
  14. all area's Avatar
    T2 , T4 and T5
    03-29-2014 12:15 AM
  15. yeewiz's Avatar
    T2 , T4 and T5
    Correct!
    03-29-2014 02:12 PM
  16. T Moore's Avatar
    Husky 8 in 1 Torx Screwdriver Set
    http://www.amazon.com/Husky-Torx-Scr...pUvbUpU2422192
    Cheaper at Home Depot
    03-29-2014 02:28 PM
  17. Daniel Mathews1's Avatar
    Does anybody know what size the torx screws are on the base of the 920?

    Thought I read somewhere that it was T5 or T6 so I went and ordered some but theyre not the right size, too big.

    If anybody knows the exact size head that would be sweet.

    Thanks
    T5 torx
    11-08-2016 08:21 AM
LINK TO POST COPIED TO CLIPBOARD
";