08-04-2015 06:33 AM
71 123
tools
  1. oscarxvita's Avatar
    Please notice that THIS IS A ROM-WRITING PROCESS WHICH NEEDS PATIENCE AND CAREFUL!!! ANY MISTAKE MAY RENDER YOUR PHONE UNBOOTABLE!!!
    STEP 1:Install Driver
    Unzip qcom usb driver(one key to setup).zip,Run setup.exe,Select“Free Bld” To Install。

    USB Driver
    http://pan.baidu.com/share/link?shar...7&uk=806646653

    2.Install Microsoft Driver
    unzip simpleio.zip,Run installsimpleio.bat as Administrator

    Step 2:Install QPST(Qualcomm Product Support Tool)
    QPST:
    QPST-2.7.399.rar_

    NOTICE:if it says it requires IE6.0 or higher,just set IE to default temporarily.

    STEP 3:Fix BootLoader
    W1 BOOTLOADER
    W1-U00 Repair bootloader.rar_

    W1-U00 Repair bootloader.rar
    MD5:1B1E4217B104D3347AE7BDC5028728F9
    SHA1:655C28EE20A2C13801753A3C42B381B4F59C117B

    Backup Download address:
    W1-U00 Repair bootloader.rar_

    W1 Update tools:
    http://pan.baidu.com/share/link?shar...8&uk=806646653

    W1 US Rom:
    http://pan.baidu.com/share/link?shar...8&uk=806646653

    CAUTION!!
    ①DO NOT TAKE OUT BATTERY IN FOLLOWING STEPS!!! AND MAKE SURE YOU HAVE ENOUGH POWER!

    ②COM Port Changes in device manager from:Qualcomm HS-USB QDLoader 9008→Qualcomm HS-USB Diagnostics 9006→WP8 UFEI USB Simple I/O(UFEI USB Simple Windows Phone I/O Protocol)


    1.Enter Qualcomm emergency mode:

    Stay power off,Use Line or metal connect these test point together as below:

    Then connect the phone to computer via USB and keep connecting the two test point until
    Qualcomm HS-USB QDLoader 9008 appears in device manager-COM ,IF there is a question mark ,please manually install from qcom_usbdriver folder.


    2.Click Start>All Application>QPST>QPST Configuration CLICK as below


    3.Start>All Application>QPST>eMMC Software Download,Click “Load Build Contents…” Select contents.xml in unrared W1-U00(C00)Repair bootloader.rar,Check "Program Boot Loaders",UnCheck "Program MMC device", Click Download


    4.After complete, the port will change into Qualcomm HS-USB Diagnostics 9006



    5.Then Check Program boot loaders,Check Program MMC device,Select Qualcomm MMC port,Click Download again.


    6.Wait for it to complete, disconnect your phone.
    NOTICE!!! If pops up TO format the disk, CLICK CANCEL!!!!!!!


    7.Press and hold "vol -" then also press and hold Power button and connect the phone to the computer, now the device manager will display WP8 UEFI USB SimpleI/O Port.



    NOW it will display this on your phone


    Start flashing Rom!!!

    Unzip WH62406270ML01Ver1008 and open WH62406270ML01.exe,Password: Huawei


    2. In“Be cautious to select” select “Not Use Safedog”
    In Please Select File,click “Firmare”and selcect the rom (*.app) you want to update ,Click “Please ChooseThe Configuration File” and select WindowsPhoneDefaultCfg.Xml in the update tools.

    After setting, click “Next ”

    9-1-.png

    This time will not appear COM, click scan&download and update the phone.
    10.png
    11.png

    YOUR phone will display this!!OK!!!!!
    13.png

    Reboot your Phone and have FUN!!
    Attached Thumbnails 12.png  
    Last edited by oscarxvita; 06-06-2013 at 01:28 AM.
    06-05-2013 03:18 AM
  2. oscarxvita's Avatar
    Ok!!!
    06-06-2013 01:32 AM
  3. Nir Dafnai's Avatar
    Can you do a video?
    06-06-2013 05:48 AM
  4. orenc17's Avatar
    thanks man it works great!!!!
    06-17-2013 08:11 AM
  5. hubai's Avatar
    Check this video

    freakyrob14 likes this.
    06-19-2013 06:33 AM
  6. Martin Ngningaye's Avatar
    Hello oscarxvita , i follow your instruction to flash my W1 from step 1 to step 4 . all was ok at step 5 , i unable to continue the dowload button don't appear . i don't know what to do. the statut show error. i have sent scren capture .Please Help me . I hope to hear fro; you very soon.

    Regards
    Attached Thumbnails capture1.png   capture2.png   capture3.png  
    06-25-2013 11:50 PM
  7. oscarxvita's Avatar
    Hello oscarxvita , i follow your instruction to flash my W1 from step 1 to step 4 . all was ok at step 5 , i unable to continue the dowload button don't appear . i don't know what to do. the statut show error. i have sent scren capture .Please Help me . I hope to hear fro; you very soon.

    Regards
    you only have to close the apps and run them as administrator, the download will be able to click.
    husyuda likes this.
    06-26-2013 12:23 AM
  8. husyuda's Avatar
    Great... Thanks wooohoooo. i managed to Flash ROM and change firmware to US
    Been thru many obstacle and finally did it, not as smooth but as u said need more patience
    Why after i changed my firmware, the WLAN hotspot was also dissapeared from my setting?
    Thanks to u i can download facebook, tweeter and youtube now
    Thanks man, u r the man ;)
    07-22-2013 08:51 AM
  9. hayawan1's Avatar
    I am having the same problem as Martin, steps 1-4 were ok, but step 5 the download button is not clickable, even after I close and re-open the app. Please help
    08-03-2013 05:01 AM
  10. engdustrial's Avatar
    I can't add the port in the QPST Configuration...
    "There was an error enabling COM. The port may not be working properly or may be busy (-2147467259 [0x80004005])

    Help?
    08-06-2013 08:07 PM
  11. engdustrial's Avatar
    Okay, I'm now stuck like Martin and hayawan1, phone is stuck in download mode.
    Running eMMC as an administrator still doesn't allow the download button to work.
    oscarxvita, any suggestions?
    08-06-2013 11:00 PM
  12. engdustrial's Avatar
    I don't know how, but I got it to work! US ROM on my W1 now! :D
    08-07-2013 01:05 AM
  13. hayawan1's Avatar
    That's good you got it working. I didn't. I ended up returnig the phone for a refund, I only purchased it because it was very cheap. I have an iPhone now but will be switching to an Android phone soon, don't know which one yet. I think I'll wait a bit longer for a Windows phone.
    08-10-2013 03:14 AM
  14. blurryfont's Avatar
    Hi I guess I bricked my phone, can anyone please help me "unbrick" itg photo.jpg. :(
    08-14-2013 10:53 AM
  15. caiannello's Avatar
    Hi Everybody.

    I had success with the above steps and flashed a ROM to the W1-U00, but I wonder if any of these tools might help me browse a live phone's file system?

    I saw that after step 3, because the device manager shows the port as "Diagnostic Mode", I thought I might be able to browse the filesystem using the "EFS Explorer".. but no luck. Besides, step 3 seems to kill the phones ability to act like a phone until all steps are completed.

    Instead, I found a way to put the port in diagnostic mode through the phone dialler by dialing ##2846579# and selecting it from the engineering menu. I don't know how much this "Diagnostic mode" has in common with the other, but It does allow the phone to run while at the same time showing up in QPST config.

    However, when I try to use the EFS Explorer in this mode, it says that this phone does not appear to support EFS Browsing. When I try to continue, it says the SPC I entered (000000) is invalid and the phone may be unresponsive for 10 seconds.

    So if some kind person could point me in the right direction of file browsing, I would be greatly appreciate it!

    Craig
    08-14-2013 01:27 PM
  16. pbomz's Avatar
    I don't know how, but I got it to work! US ROM on my W1 now! :D
    Got stuck in the same place as you did. Please let me know what you did, maybe it may be the solution for me too.
    08-20-2013 09:10 AM
  17. pbomz's Avatar
    you only have to close the apps and run them as administrator, the download will be able to click.
    you only have to close the apps and run them as administrator, the download will be able to click.
    Hi oscarxvita, I have completed all the steps successfully up until step number 4, the download button won't click. I tried running all the apps as administrator but it still won't work. I have attached the screenshots so you can see what I am getting.

    phone1.png
    phone2.png
    phone3.png

    I'd really appreciate it if you could help me out.
    Thanks.
    08-20-2013 09:44 AM
  18. pbomz's Avatar
    It worked!! I have no idea what happened, even after an entire month of trying without luck. Today,the "download" button just became clickable and I was able to go on with the process to the end. It might help to mention though for those in a similar situation, that you have to make sure you uncheck "Program Boot loaders" in step 5, as there appears to be a mistake with the instruction at that point. (You will see this in the video). The instruction says check "program boot loaders", but you must uncheck.
    08-23-2013 12:08 PM
  19. TATARIN's Avatar
    Hallo!
    I have some problem with phone now.
    On Step 6 when pop-up promt for formating, i'am clicking Ok. After this phone is not Powering On, Just vibrating.
    Bootloader still flashing, but after phone is not loading iWare uniBIOS FFU Application. Phone just light on black screen.
    So, i can not continue flashing firmware, because the phone is not recognazing like UEFI USB SimpleI/O Port.
    And now, when make procedure from start is not pop-up screen with promt for formating, and system don't show any disk on system.
    Maybe somebody have the files from disk of HUAWEI? So please give me it, i'll try to write it to my phne, maybe it help me.
    Or anybody maybe have some idea, how i can repair it.
    Thank you!
    09-02-2013 06:06 AM
  20. Adilson Afonso Mateus Tinta's Avatar
    Hallo!
    I have some problem with phone now.
    On Step 6 when pop-up promt for formating, i'am clicking Ok. After this phone is not Powering On, Just vibrating.
    Bootloader still flashing, but after phone is not loading iWare uniBIOS FFU Application. Phone just light on black screen.
    So, i can not continue flashing firmware, because the phone is not recognazing like UEFI USB SimpleI/O Port.
    And now, when make procedure from start is not pop-up screen with promt for formating, and system don't show any disk on system.
    Maybe somebody have the files from disk of HUAWEI? So please give me it, i'll try to write it to my phne, maybe it help me.
    Or anybody maybe have some idea, how i can repair it.
    Thank you!
    Quick reply to this message
    REPLY
    09-08-2013 09:05 AM
  21. wsuppa's Avatar
    when i press download in the eMMC Software Download, a sign says "image Download failed. Cookie (if present) not received", icant follow the rest of instruction.
    thank you
    09-20-2013 09:59 AM
  22. Stelios Kalintzis's Avatar
    I have problem with installation of this rom:
    It says "Failed to connect to QPST server"
    do you know why?
    EDIT: I run emc download direct fron the folder: Program files> Qualcomm>QPST>bin>emmcswdownload.exe
    And the problem solved, now I have gdr2 on my phone. :)
    Last edited by Stelios Kalintzis; 09-22-2013 at 02:50 AM.
    09-21-2013 11:02 AM
  23. Alexandre Franquinho's Avatar
    Is there any european rom with 3G support and portuguese language (or atleast an english one without loads of bugs)?
    10-13-2013 09:10 AM
  24. Alexandre Franquinho's Avatar
    10-16-2013 08:00 AM
  25. lupenyk's Avatar
    I cannot click download mode in step 5 .."Failed to connect to QPST server...i run it as administrator and direct from folder...but still nothing :/...any solution ??? Windows 8 64bit
    10-16-2013 09:27 AM
71 123

Similar Threads

  1. Replies: 1
    Last Post: 05-22-2013, 08:49 PM
  2. Replies: 4
    Last Post: 12-31-2012, 07:52 PM
  3. Replies: 47
    Last Post: 05-22-2012, 01:02 PM
  4. For those who went from leaked RTM to official Mango
    By pdawg17 in forum HTC Arrive / 7 Pro
    Replies: 0
    Last Post: 09-27-2011, 10:58 PM
  5. Replies: 23
    Last Post: 04-18-2011, 09:35 AM
LINK TO POST COPIED TO CLIPBOARD