1. Captpt's Avatar
    I've read some posts here that their 950XL won't charge using the Nokia Qi DT-910 wireless charger?? I'm quite concerned since I already purchased it while waiting for my 950XL to arrive :(
    11-28-2015 10:11 AM
  2. Likwidz's Avatar
    Didn't work with mine along with my recently purchased CR-200 . Luckily I have a couple of DT-903's it works with.
    11-28-2015 10:14 AM
  3. uselessrobot's Avatar
    I know it's not quite the same model, but my 950 works with the older DT-900 charging plate.

    On thing... While charging, I've noticed some faint interference lines when the screen is on. I'm not sure if that's a problem or if happens with the new plates.
    11-28-2015 10:18 AM
  4. mdbuilder's Avatar
    You need to set the phone in landscape and prop it up some so the coil aligns, like this: http://1drv.ms/21kiUkT
    aximtreo, Likwidz and shoe like this.
    11-28-2015 11:41 AM
  5. vincentw56's Avatar
    I ordered this: http://www.amazon.com/gp/product/B00...pUvbUpU3315139. I will let you know how it works. It should be here Saturday. It has 3 coils so hopefully one of them will be in the correct spot.
    I received this from Amazon. It works perfectly. It allows you to adjust the angle which is nice. It seems well made (at least as well as the Nokia unit). The only downside is that is doesn't come with an AC adapter. It does some with two USB cables and one is really long. I used a USB AC adapter.
    Likwidz likes this.
    11-28-2015 12:08 PM
  6. EMINENT 1's Avatar
    Noticed that the Nokia wireless charging stand and the CR 200 DOES NOT work with the XL.
    11-28-2015 01:49 PM
  7. Captpt's Avatar
    You need to set the phone in landscape and prop it up some so the coil aligns, like this: http://1drv.ms/21kiUkT
    Noticed that the Nokia wireless charging stand and the CR 200 DOES NOT work with the XL.
    That's what I've been hearing, crazy they'd move the connection on this phone compared to any other Nokia MS phone..
    mdbuilder what do mean by prop? I can't tell by the photo?
    11-28-2015 03:09 PM
  8. mdbuilder's Avatar
    That's what I've been hearing, crazy they'd move the connection on this phone compared to any other Nokia MS phone..
    mdbuilder what do mean by prop? I can't tell by the photo?
    There is a semi circle shaped piece of black rubber about 3/8" thick under the phone, it is glued to the charge plate and forms a shelf to hold the phone high enough the the centerline of the phone lines up with the center of the circle molded into the charge plate. that circle is where the coil is.
    Captpt likes this.
    11-28-2015 04:11 PM
  9. Lundon44's Avatar
    DT-910 is a no go.

    DT-903 does work... BUT mine seems to heat my phone up like nuts for some reason. I tend to leave it on over night and when I wake up the phone is very warm as if the screen was on all night or something. Not sure what's causing it.
    11-28-2015 06:01 PM
  10. Steve Gauvin's Avatar
    I have the Nokia Qi DT-910 for my old Lumia 920. I have tested it with my Lumia 950 XL and if you use a case with the 950 XL, the DT-910 doesn't work. To use the DT-910 with the Lumia 950 XL you need to put horizontaly on it without case.

    With this condition, the DT-910 is useless with Lumia 950 XL.
    11-28-2015 06:14 PM
  11. mdbuilder's Avatar
    It is too low, read my posts, look at my pics
    11-28-2015 07:54 PM
  12. mdbuilder's Avatar
    Proof, charged from 57% @9:31 to 97% @ 11:01 and 100% @ 11:07

    http://1drv.ms/21m87GR

    http://1drv.ms/21m8a5m

    http://1drv.ms/1IqQnhT

    http://1drv.ms/1XzVdQT

    In this position the phone is well aligned and barely gets warm while charging. Charge efficiency is high.
    Curtieson and wpctrlfan like this.
    11-28-2015 11:20 PM
  13. oldgreygeek's Avatar
    I have the DT-903 and it works fine with my 950xl
    11-28-2015 11:49 PM
  14. Loki1973's Avatar
    I have the Nokia Qi DT-910 for my old Lumia 920. I have tested it with my Lumia 950 XL and if you use a case with the 950 XL, the DT-910 doesn't work. To use the DT-910 with the Lumia 950 XL you need to put horizontaly on it without case.

    With this condition, the DT-910 is useless with Lumia 950 XL.
    The antenna is in the cover and since the cover can be replaced it would be nice for microsoft to offer a modified (and perhaps somewhat thinner) cover with the antenna located lower so that it can charge on the DT-910 and CR-200 (and 201). As a free replacement of course...
    Unauthorized likes this.
    11-30-2015 09:44 AM
  15. Bleak Morn's Avatar
    I didn't have a similar experience. :) Even with a spacer to get good alignment... here are my numbers:

    73% charge at 11:36 AM (estimating 49 minutes to full charge)

    ...waited 49 minutes... phone was at...

    61% charge at 12:41 PM (estimating 1 hour 10 minutes to full charge).

    I wasn't using the phone. It was in a Nokia DT-910 charging stand.

    I was using an Incipio cover sold at the MS store though so... might do better without.
    11-30-2015 01:08 PM
  16. darth furious's Avatar
    I had trouble with mine too. Here's how I do it:

    Put the 950XL in landscape mode with power/volume buttons on the bottom. The DT 910 has 2 rubber feet sticking up that your phone rests on. If you put the volume buttons between the 2 rubber feet when you rest the phone down (with the button touching one of the feet), it will charge. It's a quick way to easily put the phone in the coil's path
    shoe likes this.
    11-30-2015 03:13 PM
  17. LarsCor's Avatar
    Anyone brave enough to try modding the DT-910? Came across this mod: Nokia DT-910 Mod to work with thick cases (B… | Google Nexus 5

    Cant find a decent way to even begin opening the DT-910 though.
    12-14-2015 02:23 PM
  18. Corwin_Amber1's Avatar
    I opened up one of my DT-910s. Unfortunately in the one I opened up, the wires were too short to glue it up a little higher. Plus the Stand would probably not work with the 1520 any more. Never mind, Quickcharge is faster anyway and there are several other charging plates around the house...
    12-14-2015 06:48 PM
  19. mrkuki's Avatar
    I found that the 950XL needed to be lifted a bit so built a spacer using some of my son's spare lego. Works quite well now and it's in a 'shock absorbent dual layer' cover thing.
    12-15-2015 02:58 AM
  20. robdmau's Avatar
    I took apart the dt-910 charger and moved the coils up about .5 of an inch. Chargers fine now with a 950xl.
    02-29-2016 11:59 AM
  21. Corwin_Amber1's Avatar
    Rob, any chance you took pictures? I opened one oif mine but thought that the wires were too short and it was just too much of a hassle. Did you extend the wires?
    03-01-2016 04:07 AM
  22. Asfalloth's Avatar
    DC-50 works nice with my 950Xl too
    03-01-2016 11:38 AM

Similar Threads

  1. 950 XL & DT-903 charger extremely slow
    By caveryis in forum Microsoft Lumia 950 XL
    Replies: 27
    Last Post: 01-29-2016, 06:51 PM
  2. Any continuum video reviews? (with 950 XL)
    By LavosCracker in forum Continuum
    Replies: 1
    Last Post: 12-02-2015, 09:26 AM
  3. How can I fix an error while trying to recover my Nokia Lumia 620?
    By Windows Central Question in forum Nokia Lumia 620
    Replies: 0
    Last Post: 11-28-2015, 10:01 AM
  4. Replies: 1
    Last Post: 11-28-2015, 09:01 AM
  5. What is the best app to pin websites to WP10 start screen with a custom icon?
    By Windows Central Question in forum Microsoft Lumia 950 XL
    Replies: 0
    Last Post: 11-28-2015, 07:33 AM
LINK TO POST COPIED TO CLIPBOARD