1. nebelwerfer's Avatar
    Good morning

    I got issue with my comp. Three days ago I've put my computer on, and it started and after few seconds it stopped, and restarted again, but after restart it went into Bios screen with message

    "Please enter setup to recover settings
    After setting an Intel Optane Memory or the Raid configuration was build, SATA mode selection must be changed to Raid mode to avoid unknown issue,
    If OS was previously installed as AHCI, set SATA mode to AHCI in Bios, press F1....
    Everything is setup as it should, I got SATA in AHCI mode so I dont know where it message comes from since I checked Bios couple of times and settings are correct.

    My comp specification
    ASUS Rog x299 STRIX XE
    9900X
    2*2080TI EVGA
    Samsung 970 M2
    Windows 10 20H2

    Since then I updated Bios to new version, I got RAID on two SSD's and I got Samsung970 M2 for boot. When I put comp on it cannot boot, I have to reset couple of times to boot into Bios (there's a message E2 on the display).
    Windows 10 20H"2 works normally right now , but when I'll turn off my comp it's not gonna boot on the next day.
    What is it??
    Help greatly appreciated.
    01-17-2021 06:39 AM
  2. TechFreak1's Avatar
    Good morning

    I got issue with my comp. Three days ago I've put my computer on, and it started and after few seconds it stopped, and restarted again, but after restart it went into Bios screen with message

    "Please enter setup to recover settings
    After setting an Intel Optane Memory or the Raid configuration was build, SATA mode selection must be changed to Raid mode to avoid unknown issue,
    If OS was previously installed as AHCI, set SATA mode to AHCI in Bios, press F1....
    Everything is setup as it should, I got SATA in AHCI mode so I dont know where it message comes from since I checked Bios couple of times and settings are correct.

    My comp specification
    ASUS Rog x299 STRIX XE
    9900X
    2*2080TI EVGA
    Samsung 970 M2
    Windows 10 20H2

    Since then I updated Bios to new version, I got RAID on two SSD's and I got Samsung970 M2 for boot. When I put comp on it cannot boot, I have to reset couple of times to boot into Bios (there's a message E2 on the display).
    Windows 10 20H"2 works normally right now , but when I'll turn off my comp it's not gonna boot on the next day.
    What is it??
    Help greatly appreciated.
    1) Have you checked the event logs?
    2) Any new updates installed other than the BIOS update?
    3) Raid Drivers update to date?
    4) Have you checked your sleep/hibernate settings? - this poster appears to have a similiar problem to you:
    https://rog.asus.com/forum/showthrea...after-shutdown

    I couldn't find anything else similar, albeit it was a 10 second search lol...
    01-17-2021 12:16 PM

Similar Threads

  1. windows activation
    By Amir hossein Jalalian in forum Ask a Question
    Replies: 4
    Last Post: 01-18-2021, 03:38 AM
  2. You can ditch Edge as the default browser, and here's how on Windows 10.
    By WindowsCentral.com in forum Windows Central News Discussion & Contests
    Replies: 0
    Last Post: 01-16-2021, 06:11 AM
  3. Check out Windows Central's Best of CES 2021 picks
    By WindowsCentral.com in forum Windows Central News Discussion & Contests
    Replies: 0
    Last Post: 01-15-2021, 01:11 PM
  4. The Future Tech Awards have arrived with support from five special sponsors
    By WindowsCentral.com in forum Windows Central News Discussion & Contests
    Replies: 0
    Last Post: 01-15-2021, 12:11 PM
LINK TO POST COPIED TO CLIPBOARD